Dereike specializes in producing and selling scroll high-pressure air pumps, RB ring high-pressure blowers, scroll high-pressure blowers, permeable high-pressure blowers, Taiwan high-pressure blowers with high-end configuration and quality all passed S test by the national professional department. Widely applicable to: industrial, agricultural, chemical, sewage treatment aeration, aquaculture oxygen, grain transport, cutting prototype special and other uses.
Double impeller scroll high pressure air pump configuration:
1. Shell material: high pressure scroll air pump uses super strength, die-casting aluminum and Benz car wheel will be the same aluminum, compared with the general, die-casting aluminum is more solid, compared with iron shell air pump, more lightweight role.
2. Motor performance: High-voltage scroll pump is a wide-band, wide-voltage motor, included in: single-phase 110V/230V industrial three-phase: 220/380/415/660V, motor frequency can be 45-75HZ frequency modulation, IP54 protection level F insulation level, its advantage is that the domestic motor can not reach the process, favored by domestic and foreign customers.
3. Fan oil seal: High-pressure scroll pump adopts German MERKEL oil seal, German MERKEL (Merkel) material uses fluorine rubber to withstand - 25 to 300 C. Compared with the general oil seal, the lip edge temperature is higher than the working medium temperature of 20 ~ 50 C, and the performance is more stable, maintenance-free, and the service life is longer.
4. Fan Bearing: The core components of high-pressure scroll pump are SKF, NSK brand bearings. The bearings can withstand up to 350 degrees Celsius and 4000 revolutions per minute. For domestic Luoshafts, humanistic bearings, stable performance, low noise, maintenance-free, longer life, can ensure that the fan runs longer.
Vortex High Pressure Air Pump:
1. The motor of the Vortex Air Pump is directly connected to the impeller and belongs to high speed. The bearings need to be regularly maintained with butter to prevent damage (including impeller bearings).
2. The shaft power and pressure of the motor are proportional. In order to prevent the increase of shaft power caused by long-term limit pressure and the overload of the motor, the pressure relief valve is often used. It is a unloading valve. When the pressure exceeds the pressure set by the relief valve, the relief valve will automatically open and release the excess pressure, thus protecting the motor of the high-pressure fan
3. The internal mechanism of the scroll pump is relatively close, and the clearance between the impeller and the casing is very small. Therefore, the impurities and dust should be filtered. For debris, usually the inlet is equipped with fine, dust, often used as a filter. According to the different use site, it often uses different filter elements with different filtering accuracy. Different filter elements have different maintenance methods and service life. It is necessary to ask clearly when ordering.
Vortex high-pressure air pump features:
1. Super silent, no noise: the motor directly operates, through the addition of an integrated sound pinning facilities, improve the high-pressure fan noise phenomenon, so as to achieve the silent effect.
2. Reliability is high. The machine can still operate safely when the service condition changes. Except for the impeller, the high-pressure blower has no other action, so its reliability is almost maintenance-free. It has the following advantages: high compression ratio; low operating temperature of bearings; long service life of lubricating grease; and no maintenance.
3. Installation is easy to be equipped with complete, can be installed and used at any time, for compressed air or vacuum, can also be installed in the horizontal or vertical direction.
4. When the oil-free and pollution-free impeller rotates, it does not contact with any parts and is free of lubrication, so it can guarantee 100% pollution-free. Vortex high-pressure air pump sewage treatment aeration special high-pressure vortex air pump custom gas ring vacuum pump.
Type: Gas transfer pump
Material Aluminum Alloy
Principle of gear pump
Vacuum degree
Driving mode
Performance High Voltage
Purpose: Sewage pump
Transport media: sewage pump, impurity pump
Power 7.5 (kw)
Limit pressure 5700 (pa)
Shape size 1*2B*2110/*2145
Pump Shaft Position Horizontal
Selection of pumping rate (l/s)
Selection of pumping capacity
Maximum working pressure 57KPa
Weight 73 (kg)
Voltage 380V (V)
Discharge caliber 40 (mm)
Head 600 (m)
Flow: 320 (m3/h)
Number of impellers 58
Specification Material
Brand
Model YX-72S-5
Quantity 1
Reference Price 2600